Ambiance Fireplaces INT-200 Istruzioni per gli Interventi

JUNE 2012 INT-REV-05 —Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. W

8 MINIMUM FINISHED OPENING DIMENSIONS FRAMING WALL ENCLOSURE ROUGH OPENING HORIZONTAL TERMINATION: 44-1/2”(1130mm) High

9 Determine exact position of your fireplace, including hearth height, width, and depth, (if applicable). If possible, place fireplace in such a mann

10 12"13mm19 12"495mm41 38"1051mmTYPICAL INSTALLATION OPTIONS TYPICAL HORIZONTAL INSTALLATION TYPICAL VER

11 10"254mm12 12"318mm14 12"368mm16 12"419mm13" (330mm)11" (279mm)9" (229mm)13 12"343mm1"25mmMANTEL REQUI

12 This fireplace is manufactured for use with Natural Gas. Follow instructions included with conversion kit if converting to LP g

13 Refer to the vent systems manufacturer's installation manual for complete installation instructions. Installation must conform with the venti

14 VERTICAL TERMINATIONS MINIMUM: 45˚ elbow + 2ft. (610mm) + termination cap. MAXIMUM: 45˚ elbow + 50ft. (15.2m) + termination cap. MAXIMUM (if u

15 HORIZONTAL & VERTICAL COMBINATION TERMINATIONS MAXIMUM: 18ft. (5.49m) horizontal + 18ft. (5.49m) vertical + cap. [36ft. (10.98m) total]. MA

16 1. Terminations against vinyl siding must use a vinyl siding protector. Follow instructions included. 2. DO NOT RECESS TERMINATION KIT INTO OU

17 Roof Pitch H (Min.) Ft. H (Min.) m Flat to 6/12 1.0 0.30 Over 6/12 to 7/12 1.25 0.38 Over 7/12 to 8/12 1.5 0.46 Over 8/12 to 9/12 2.0 0.6

18 #INT-500 LOG SET INSTALLATION #3 #2 #1 Install #5 - #10 logs as shown above, aligning with notches in base logs, an

19 1. Use remote to turn fireplace off. 2. Shut off gas supply at manual shut-off valve. Disconnect gas line flex tube from the manual shut-

20 Proper burner venturi placement over burner orifices (cut-away side view) CONTROL BOARD INSTALLATION 1. Place control

21 GRILL SET INSTALLATION Thread screws into nuts grill ends and secure to lower grill opening. 3 2 Slide flange on upp

22 WIRING SCHEMATICS IMPORTANT THIS SYSTEM REQUIRES ELECTRICITY (120V) AND / OR BATTERIES TO OPERATE. USING BATTERY BACK UP WILL OPERATE BURNER ON

23 Pilot Igniter Flame Sensor PILOT ASSEMBLY Figure 23c CONTROL SYSTEM COMPONENTS Figure 23a REMOTE CONTROL GAS VALVE Outlet pressure tap Stepper m

24 SYSTEM OPERATION INITIALIZING THE SYSTEM FOR THE FIRST TIME 1. Set ON/OFF rocker switch to OFF position. 2. Install 4 AA batteries (included i

25 SYSTEM OPERATION ROOM THERMOSTAT (Remote Control Operation) The Smart Thermostat function adjusts flame height based on set temperature and act

26 SYSTEM OPERATION This system has the option of a continuous (standing) pilot feature. This allows you to change from a spark-to-pil

27 SYSTEM OPERATION S. I.T. PROFLAME 2 IFC IGNI TI ON AND RESET INFORMAT ION RESET IFC CONTROL MODULE WHEN SYSTEM GOES INTO LOCK OUT Reset Us

1 TABLE OF CONTENTS TABLE OF CONTENTS Table of Contents 1 SAFETY INFORMATION Safety Information 2 COMMONWEALTH OF MA

28 LIGHTING AND SHUTDOWN FOR YOUR SAFETY - READ BEFORE OPERATING WARNING IF YOU DO NOT FOLLOW THESE INSTRUCTIO

29 LIGHTING AND SHUTDOWN (cont.) 5 MINUTES Power OFF Power ON Power OFF OFF OFF ON 1 4 1 3 2 5 3 2 Figure 29b Figure 29a STOP! Read safety informa

30 PRESSURE TESTING INLET PRESSURE TEST: Outlet (Manifold) Pressure Screw Inlet Pressure Screw Figure 30a IMPORTANT Pressure check taps for manifold

31 FACTORY SET BURNER TUBE VENTURI SETTINGS (ADJUST AS NECESSARY FOR YOUR INSTALLATION) NATURAL GAS LP (PROPANE) GAS 100% CLOSED 5/8” (16mm) OPE

32 FINALIZING THE INSTALLATION RESTRICTOR ADJUSTMENT: This fireplace is shipped with the restrictor in the open position. After installation it may b

33 MAINTENANCE Burner Ports Annual cleaning of burner system is required. Vacuum all components thoroughly. Visually c

34 TROUBLESHOOTING ATTENTION TROUBLESHOOTING MUST BE PERFORMED BY A QUALIFIED TECHNICIAN. Before proceeding with the steps in the following troubles

35 TROUBLESHOOTING PILOT AND BURNER EXTINGUISH WHILE IN OPERATION No LP in tank. Check and refill if necessary. Glass frame assembly not installed co

36 CONVERSION KIT INSTRUCTIONS PREPARE THE FIREPLACE: 1. Remove upper hood, upper louver, glass assembly*. 2. Remove logs*. 3. Remove back burn

37 COMPLETE THE CONVERSION: 1. Adjust front burner venturi setting by loosening screw, adjusting cap and retightening screw. NAT: 100%

2 SAFETY INFORMATION Installation and repair should be done only by a qualified service person. The appliance

38 *Consult your dealer for information on optional accessories available for this fireplace. This appliance tested & certified by: OMNI - Test L

39 LIMITED WARRANTY WARRANTY CONDITIONS & REQUIREMENTS: 1. You are the original purchaser. This warranty is not transferable. 2. Installation of

40 LIFETIME WARRANTY LIFETIME WARRANTY THIS LIFETIME WARRANTY COVERAGE WILL BE EXTENDED AS DESCRIBED BELOW PROVIDED ALL WARRANTY CONDITIONS AND REQ

3 COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS For all sidewall horizontally vented gas fueled equipment installed in every dwell

4 FIREPLACE DIMENSIONS DESCRIPTION Height Width Back Width Depth Opening Width Glass Frame Height Stand-off Height Front to Vent Center (Vert.

5 PLACEMENT CLEARANCE REQUIREMENTS This fireplace must be installed on a level surface capable of supporting the fireplace and venting. Fireplace must

6 PREPARE THE FIREPLACE Top stand-off brackets and stand-off heat shields are attached to fireplace top in a flat stat

7 When installed, nailing flanges provide minimum 1/2” (13mm) clearance from fireplace sides. FRAMING STUD NAILING FLANGE FRAMING STUD 1/2” (13mm) CL